7 Reasons Your Circuit Breakers Keep Tripping
Last Updated: November 10, 2026
Quick Summary
Circuit breakers tripping is usually caused by one of seven faults: an overloaded circuit, a short circuit, an earth fault, a loose connection, an ageing breaker, a power surge, or a faulty appliance. An overload trips after heavy use, while a short circuit trips instantly every time you reset it.
An overloaded circuit is the most common reason for circuit breakers tripping.
A short circuit trips instantly on reset, often with a bang.
Never replace a tripped breaker with one of a higher rating.
Test one appliance at a time to find a faulty appliance.
Call an electrician if a breaker will not reset or smells of burning.
Breaker keeps tripping? Find out why.
Bright Sparx Electrical traces tripping faults and restores your power safely, with certified work.
Table of Contents
Circuit Breaker Tripping Causes: The 7 You Need to Know
If you are dealing with circuit breakers tripping, the cause is usually one of seven faults: an overloaded circuit, a short circuit, an earth fault, a loose connection, an ageing breaker, a power surge, or a faulty appliance. This guide shows you how to find the cause safely, and when to stop and call a qualified electrician.
A circuit breaker is a safety switch inside your consumer unit that cuts the power when current exceeds a safe level. It protects your wiring from overheating and fire. When it trips, it is doing its job, not failing.
Below, we cover the seven causes in order of how often we find them. We also show you how to tell an overload from an earth fault, and exactly what to do before you touch anything.
Overloaded Circuits and Excessive Electrical Demand
An overloaded circuit is the most common reason for circuit breakers tripping. You have plugged too much into one circuit, so the demand exceeds its rated capacity. The breaker senses the overcurrent and cuts the power.
Modern homes run far more appliances than their wiring was designed for. Kettles, heaters, and tumble dryers draw heavy current. Put two of them on one circuit and it will trip.
Watch for these signs:
The breaker trips when you use a certain appliance
It happens most in winter, when heaters go on
Several sockets on one circuit run hot
The fix is simple: spread the load. Move appliances to different circuits or use one high-draw item at a time.
Short Circuits and Damaged Wiring
A short circuit happens when a live wire touches a neutral or earth wire. Current takes a shortcut and surges to a huge level. The breaker trips instantly, often with a bang.
Damaged wiring is the usual culprit. Rodents chew cables. Screws pierce wires behind plasterboard. Old insulation cracks with age. A common mistake is ignoring a breaker that trips the moment you reset it. That points to a short, not an overload. If you suspect damaged wiring, read our guide to the warning signs your house needs rewiring before you use that circuit again.
Earth Faults, Earth Leakage and Moisture
An earth fault occurs when live current escapes to earth through a person, water, or a damaged appliance. This is the most dangerous fault of all. It can give a shock before the breaker reacts.
Moisture is a frequent trigger. Water gets into outdoor sockets, garden lights, or a leaking roof. Damp then creates a path for earth leakage. RCDs and RCBOs detect this and trip fast to protect you.
Never ignore a breaker that trips in wet weather. Find the damp source and isolate the circuit.
Loose Connections, Ageing Breakers and Power Surges
A loose connection creates resistance, which builds heat. Over time it can melt insulation or start a fire. Ageing breakers also weaken: the trip mechanism wears out and no longer holds. Power surges from lightning or grid faults can trip devices too.
Loose connections are a job for a qualified electrician. Do not open the consumer unit yourself. If you notice a burning smell or visible damage, isolate the supply and call for help. For ageing hardware, our guide on the signs your consumer unit needs replacing explains what to look for.
Overload or Earth Fault? How to Tell the Difference
You can often tell an overload from an earth fault by when the breaker trips. An overload trips after a period of heavy use. An earth fault or short circuit trips instantly, every time you reset it.
Symptom | Likely Cause | What It Means |
Trips after minutes of use | Overload | Too much load on the circuit |
Trips instantly on reset | Short circuit | Live wire touching another wire |
Trips in wet weather | Earth fault | Moisture causing earth leakage |
Trips randomly, now and then | Loose connection or ageing breaker | Needs inspection |
Trips when one appliance runs | Faulty appliance | Isolate that appliance |
This table covers most cases. If your pattern does not fit, treat it as an intermittent fault and get it checked.
What to Do When a Circuit Breaker Trips: Step by Step
Follow these steps in order. Stop at any point if you feel unsure, and never open the consumer unit itself, the wiring behind the cover is live even when a breaker is off.

Isolate the supply. Switch off and unplug appliances on the affected circuit. If the trip has affected several circuits (common with a single RCD), unplug appliances on all of them.
Find the affected circuit. Check the consumer unit label to identify which breaker or RCD has tripped. If the label is missing or unclear, note which rooms have lost power.
Reset the device. Push the switch fully to the off position, then back to on. For an RCD, press the test button first if it has one, then reset.
Observe what happens. If it holds, the cause was likely a temporary overload or a one-off appliance fault. If it trips again immediately, stop, this points to a short circuit or a faulty device.
Test one appliance at a time. Plug each back in and run it, watching for a trip. The last appliance you tested before a trip is the likely culprit.
Note the pattern. Does it trip after minutes (overload), instantly (short circuit), or in wet weather (earth fault)? This tells you the cause.
Leave it off if it will not reset. Do not keep forcing it. A breaker that will not reset is a fault that needs professional attention.
If the breaker will not reset: This is the most common urgent scenario, and the correct response is to stop. A breaker that trips instantly every time you reset it indicates a short circuit or a faulty breaker.
Distinguishing overload from short circuit or earth fault: The trip timing is your best clue. An overload trips after a period of heavy use, minutes or longer, and often in winter when heaters are on.
Watch out: never replace a tripped breaker with one of a higher rating to stop it tripping. The breaker is sized to protect the cable, and a higher-rated breaker allows the cable to overheat and start a fire.
If the breaker will not reset, stop. Before you book anyone, it helps to understand hidden costs in electrical repairs so you can budget with confidence.
Faulty Appliance Tripping Breaker: How to Track It Down
When a faulty appliance tripping the breaker is the cause, the pattern is clear. The breaker trips only when that one item runs. Kettles, irons, washing machines, and old fridge freezers are common offenders.
Use this method:
Unplug every appliance on the circuit
Reset the breaker
Plug in one appliance and run it
Repeat until the breaker trips
The last appliance you tested is the likely fault. Unplug it for good and test the circuit again. If the breaker holds, you have found your culprit.
RCD and RCBO Trips: Different Devices, Different Fixes
An RCD (residual current device) and an RCBO (residual current breaker with overcurrent protection) are not the same as an ordinary miniature circuit breaker (MCB), and confusing them leads to misdiagnosis. An MCB protects against overload and short circuit only.
In a typical consumer unit, you can identify the devices by their markings and test buttons. MCBs are usually single-width switches with a rating in amps (e.g. B32).
The trip pattern tells you which device has operated and why:
MCB trips after a period of heavy use: overload. Spread the load or reduce demand.
MCB trips instantly on reset: short circuit. Isolate the circuit and call an electrician.
RCD or RCBO trips in wet weather or after appliance use: earth leakage. Moisture, damaged cable insulation, or a faulty appliance is the usual cause.
RCD trips with no obvious pattern: a cumulative earth leakage fault, often from several appliances each leaking a small amount. Unplug appliances one by one to isolate.
A common pattern with RCDs is nuisance tripping caused by older appliances, fridges, freezers, and washing machines are frequent offenders because their heating elements and motors can leak small currents to earth as they age.
Watch out: never bypass an RCD or RCBO by taping the switch on or removing it from the circuit. These devices are your primary protection against electric shock, and disabling one leaves the installation unsafe.
If an RCD or RCBO will not reset even with all appliances unplugged, the fault is in the fixed wiring or the device itself. This is not a DIY repair.
When to Call an Electrician for a Tripping Breaker
Call a qualified electrician when a breaker will not reset, trips instantly, or trips with a burning smell. These point to faults that are unsafe to handle yourself. Electrical work carries real risk of shock and fire.
You should also call if:
The breaker trips repeatedly with no clear cause
You see visible damage or scorch marks
The fault is intermittent and hard to pin down
Your consumer unit is old or has no RCD protection
A common mistake is putting off the call. If you are unsure whether the fault justifies a visit, our guide on the signs you need an electrician to find an electrical fault will help you decide. Once you have decided to book, check the electrician's certification status first, so you know the work will be done properly.
At Bright Sparx Electrical, our in-house team is Part P registered and 18th Edition compliant. All work is certified and insured. We offer a free full inspection, so you get a clear answer before any work starts.
A tripping breaker is your wiring telling you something is wrong. Guessing at it wastes time and can put your home at risk. Bright Sparx Electrical finds the real fault with a free full inspection, fixes it with certified, insured work, and restores your power safely.
Frequently Asked Questions
Is it safe to keep resetting a tripping circuit breaker?
Resetting once to see if the trip was a one-off is fine. Resetting it repeatedly is not. If the breaker trips again straight away, stop and leave it off: something on that circuit is faulty, and forcing it back on risks overheating, burning at the contacts or a fire. Repeated tripping is the protective device doing its job, so treat it as a warning rather than an inconvenience to override.
Can a faulty appliance make a circuit breaker trip?
Yes, and it is one of the most common reasons for circuit breakers tripping. A failing kettle, washing machine, tumble dryer or heater can draw more current than normal or leak current to earth, which trips the breaker or RCD. Unplug every appliance on the affected circuit, reset the breaker, then plug them back in one at a time until it trips again. The last appliance you connected is the likely culprit.
What should I do if the breaker trips as soon as I reset it?
Leave it off. A breaker that trips instantly points to a short circuit, an earth fault or damaged wiring rather than an overload, and these need proper testing with insulation resistance and continuity checks. Do not tape the switch on or swap in a larger breaker. Isolate the supply to that circuit and call a qualified electrician, because a fault like this can be hidden inside a wall or under a floor.
When should I call an electrician about a circuit breaker that keeps tripping?
Call an electrician if the breaker will not reset, if it trips with nothing plugged in, if you notice a burning smell, scorch marks or buzzing at the consumer unit, or if tripping happens at random times over days. Intermittent faults, moisture ingress and ageing breakers all need test equipment to diagnose. A qualified electrician can identify the affected circuit, test the protective devices and confirm whether the breaker itself has failed.



Comments